Insteon MorningLinc (2458A1) Quick Start Manuel d'utilisateur télécharger pdf

Page 1 of 1

Rev. 09-20-2011

SmartLabs Limited Warranty – SmartLabs warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be

free from defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by

misuse or neglect.

SmartLabs, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845

Status LED

Controlling MorningLinc from an INSTEON Controller

Individual commands can be Linked to the On and Off buttons on your Controller. For example, you can Link the door to lock

when you press the On button and unlock when you press the Off button on your Controller.

NOTE: LOCK and UNLOCK commands must each be Linked to a separate button. Commands cannot be toggled on one

button unless you are using a Controller that allows toggle mode (e.g., KeypadLinc

™

To Link to an On button:

1) Use the Set button to put your lock into the desired state (what action you would like the lock to perform when you press

the On button)

2) Set your Controller to Linking Mode. (For most Controllers, press & hold an On or Scene button for 10 seconds, or the Set

button for 3 seconds.)

You will have 4 minutes to complete the next step before Linking Mode automatically times out.

3) Press & hold the Set button on MorningLinc for 3 seconds

The MorningLinc Status LED will flash once, and then turn on solid if the door is locked or turn off if the door is

unlocked

4) Confirm that Linking was successful by locking/unlocking the door and pressing the On button you just Linked to

MorningLinc should respond appropriately

To Link to an Off button:

1) Use the Set button to put your lock into the desired state (what action you would like the lock to perform when you press

the Off button)

2) Set your Controller to Linking Mode. (For most Controllers, press & hold an On or Scene button for 10 seconds or the Set

button for 3 seconds.)

You will have 4 minutes to complete the steps 3 and 4 before Linking Mode automatically times out.

3) Double-tap the Set button on MorningLinc and wait for 3 seconds before next step

4) Press & hold the Set button on MorningLinc for 3 seconds

The MorningLinc Status LED will flash once, and then turn on if the door is locked or turn off if the door is unlocked

5) Confirm that Linking was successful by locking/unlocking the door and pressing the Off button you just Linked to

MorningLinc should respond appropriately

Quick-Start Guide

MorningLinc

– INSTEON

Morning Industry

RF Doorknob/Deadbolt Controller

Model: 2458A1

Introduction

MorningLinc consists of a specially-wired ICON Appliance Module,

which will allow you to lock or unlock your Morning Industry RF

deadbolts and door locks (up to fifteen) with the press of a button

on an

Linked INSTEON Controller.

Installation

When installing MorningLinc, use an outlet or extension cord to keep the unit within five feet of the door lock fixture. Once

installation is complete, MorningLinc can be moved to another outlet (up to 30 feet away from the door lock fixture).

1) Be sure you have properly installed at least two Access Points or other dual-band products. Search for dual-band

INSTEON products at: http://www.smarthome.com/dualband

2) Plug MorningLinc into an unswitched wall outlet

The MorningLinc Status LED will turn on solid

3) Use a screwdriver to remove the cover plate from the door lock fixture. Then, tap its Set button (labeled “S”).

The door lock fixture will beep

4) Tap the Set button on MorningLinc

After a few seconds, the door lock fixture will double-beep

The MorningLinc Status LED will turn off

5) If you wish to control multiple door locks with MorningLinc, repeat steps 3 and 4 with each additional door lock fixture

6) Tap the Set button on MorningLinc to toggle the door lock fixture locked and unlocked

NOTE: The MorningLinc Status LED will follow the last INSTEON command it received. When the door is manually locked/unlocked

from the keypad or the lock itself, the LED will not change until it receives an INSTEON command (either from a Linked Controller or

the Set button on Mornin

Linc

)

. It ma

take 3-5 seconds for the door lock fixture to respond to INSTEON commands.

Complete Instructions, Troubleshooting, and Tech Support

Owner’s Manual: http://www.smarthome.com/manuals/2458a1.pdf

Call:

Tech. Support @ 1-800-SMARTHOME (800-762-7846)

http://www.smarthome.com/contactus.html

Set button

Quick-Start Guide 1

Résumé du contenu

Page 1 - Quick-Start Guide

Page 1 of 1 Rev. 09-20-2011 SmartLabs Limited Warranty – SmartLabs warrants to original consumer of this product for a period of 2 years from date o

Commentaires sur ces manuels

Pas de commentaire

Insteon MorningLinc (2458A1) Quick Start Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Insteon MorningLinc (2458A1) Quick Start. INSTEON MorningLinc (2458A1) Quick Start User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Insteon MorningLinc (2458A1) Quick Start