Insteon Ballast Dimmer - 2475DA2 Quick Start Manuel d'utilisateur télécharger pdf

2475DA2 Rev. 7/24/2013 8:55 AM / See Owner’s Manual for Warranty Information.

Protected under U.S. and foreign patents (see www.insteon.com/patents)

1) Write down the INSTEON ID found on the front of the unit

(XX.XX.XX)

2) Turn off breaker/fuse and verify that the power is off

3) Disconnect wires from existing switch

4) Connect wires per diagram

5) At the ballast location, disconnect the wires from the fixture

you will be controlling and ensure that you have ½ inch of

bare wire on the ends

6) See the diagram to identify and connect the line, load,

neutral DC(+) and DC(-) wires on Ballast Dimmer. Be sure

you have correctly identified the wires in the junction box

before connecting them.

7) After ensuring wires are firmly connected and that there is

no exposed wire, turn on breaker/fuse

After a few seconds, load will turn on

8) Test Ballast Dimmer connection by tapping set button a

couple times

Ballast Dimmer load will respond appropriately

9) Link Ballast Dimmer to your INSTEON keypad or other

INSTEON controller. See Make Ballast Dimmer a

Responder.

10) Gently place Ballast Dimmer into the fixture box, making

sure nothing could accidentally press on the set button

11) Reinstall the fixture

Quick Start Guide

Ballast Dimmer

INSTEON

Remote Control 0-10VDC Ballast Dimmer or Dual Switch

Model: 2475DA2 (US), 2446-422 (EU), 2446-522 (AUS/NZ)

About Ballast Dimmer

This in-line ballast control module supports two different operational modes: dimmer and dual-relay. For use in new construction

or retrofit (inside or outside the fixture) where saving energy is a priority.

RJ-10 Mini-modular jack pin-outs:

Pin 4

(Left side)

Pin 3 Pin 2 Pin 1

Group 1: triggers when switch between pin 3 & 4 is closed

Group 2: triggers when switch between

pin 3 & 4 is opened

Group 3: triggers when switch between

pin 2 & 4 is closed

Group 4: triggers when switch between pin 2 & 4 is opened

Ground Group 1 - 2 Group 3-4 12-15VDC

Install Ballast Dimmer for Dimmable Ballast

Note: use with branch circuit breakers 15 Amperes or fewer.

Line (Black)

Neutral (White)

Set button

Status LED

Load 2 (Red)

Load 1 (Red/Black)

0-10VDC + (Purple)

DC ground (Grey)

The hot feeding this circuit is paralleled from the hot

connection on the keypad keeping both devices powered at

all times and using existing wiring.

RJ-10 jack

0-10VDC + (Purple)

DC ground (Grey)

Load 2 (Red)

Neutral (White)

Line (Black)

1 2

Quick Start Guide 1

Résumé du contenu

Page 1 - Quick Start Guide

2475DA2 Rev. 7/24/2013 8:55 AM / See Owner’s Manual for Warranty Information. Protected under U.S. and foreign patents (see www.insteon.com/patents) ©

Page 2

2475DA2 Rev. 7/24/2013 8:55 AM / See Owner’s Manual for Warranty Information. Protected under U.S. and foreign patents (see www.insteon.com/patents) ©

Commentaires sur ces manuels

Pas de commentaire

Insteon Ballast Dimmer - 2475DA2 Quick Start Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Insteon Ballast Dimmer - 2475DA2 Quick Start. INSTEON Ballast Dimmer - 2475DA2 Quick Start User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Insteon Ballast Dimmer - 2475DA2 Quick Start